Free shippingOn every online order shipped within the contiguous U.S. Valid only for orders placed through our website.
Safety Through Innovation · Made in the USA
Free shippingOn every online order shipped within the contiguous U.S. Valid only for orders placed through our website.
Machine guarding risk assessments, fall hazard assessments, electrical evaluations, and stop time measurement and safety device validation.
Showing all 5 products
These services evaluate hazards and safeguards where the work happens. They are grouped into four subcategories: machine risk assessments, machine validation, electrical validation and fall hazard assessments. Together they answer three practical questions: where are the hazards, do the existing safeguards perform, and what has to change before an upgrade?
The machine guarding risk assessment is an on-site, machine-by-machine review of a floor against OSHA 29 CFR 1910.212, ANSI B11 and ISO standards. Each hazard identified is risk-ranked, which gives guarding decisions a clear order of priority.
The OSHA baseline is 1910.212(a)(1): one or more methods of machine guarding must protect the operator and other employees from hazards such as the point of operation, ingoing nip points, rotating parts, and flying chips and sparks, using methods such as barrier guards, two-hand tripping devices and electronic safety devices. 1910.212(a)(3)(iv) lists machines that usually require point of operation guarding, including guillotine cutters, shears, power presses and milling machines. On the consensus side, ANSI B11.0 sets out the risk assessment process for machinery, from identifying hazards to estimating, evaluating and reducing risk, and now contains the guidance formerly published as the B11.TR3 technical report. ISO 12100 sets out general principles of risk assessment and risk reduction for machine design.
Machine stop measurement and safety device validation is arranged by contacting Odiz. Stopping time matters because a presence-sensing device or two-hand control only protects people if it sits far enough from the hazard for the machine to stop first. For mechanical power presses, OSHA 1910.217 ties the minimum safety distance of presence-sensing devices and two-hand controls to the press’s measured stopping time, and ANSI B11.19 sets performance requirements for safeguarding devices more broadly. ISO 13849-2 covers validation of the safety-related parts of control systems by analysis and testing.
A machine electrical evaluation documents, analyzes and prepares machine control systems for safety upgrades such as interlocks, trap key systems and other guarding integrations, and machine safety system electrical validation covers the electrical side of a machine’s safety system. ISO 13849-1 gives design principles for the safety-related parts of control systems that such upgrades involve.
The fall hazard assessment is for workplaces concerned about fall hazards and unsure where to start, including those working through OSHA 1926.501 requirements. In construction, 1926.501 sets the duty to have fall protection, for example where an unprotected side or edge is 6 feet or more above a lower level, and the systems used must meet the criteria in 1926.502. In general industry, 1910.140 sets performance, care and use criteria for personal fall protection systems. Related equipment is in fall protection.
Between on-site visits, the risk assessment apps and machine safety apps record guided assessments, stop time checks and regular safeguard inspections.
It is an on-site, machine-by-machine review of your floor against OSHA 29 CFR 1910.212, ANSI B11 and ISO standards. Each hazard identified is risk-ranked, so guarding work can be prioritized across all of the machines reviewed rather than one at a time.
Safeguarding devices such as light curtains and two-hand controls must be located far enough from the hazard that the machine stops before a hand can reach it. For mechanical power presses, OSHA 1910.217 bases the minimum safety distance on the press's measured stopping time.
When you are concerned about fall hazards in your workplace and unsure where to start, or need help with OSHA 1926.501, the construction standard that sets the duty to have fall protection. Related harnesses, anchors and other equipment are in the fall protection category.
A machine electrical evaluation documents and analyzes a machine's control system to prepare it for safety upgrades such as interlocks and trap key systems. Machine safety system electrical validation addresses the electrical side of the safety system itself. The electrical validation category covers both services.
OSHA 1910.212(a)(3)(iv) lists machines that usually require point of operation guarding: guillotine cutters, shears, alligator shears, power presses, milling machines, power saws, jointers, portable power tools, and forming rolls and calenders. A risk assessment confirms what each machine on your floor needs.