Safety Through Innovation · Made in the USA

574.318.4333Email UsODIZ AI Login
OdizSafety
ProductsServicesOdiz AICompany
Get an AssessmentGet an Assessment

Start a project

Let’s engineer a safer floor.

Schedule an AssessmentSchedule an Assessment
574-318-4333info@odiz.com
Odiz — Safety Through Innovation. Made in the USA.

Industrial safety, engineered from assessment through sustained compliance. Based in South Bend, serving manufacturers across North America.

Appearance

Solutions

  • Machine Safety
  • EHS Compliance
  • Laser Safety
  • Safety Software

Services

  • Machine Guarding Risk Assessment
  • Engineering & Design
  • Validation
  • All Services

Products

  • Machining
  • Metal Forming
  • Electronic Safety Enclosures
  • Accessories
  • All Products

Company

  • About Us
  • Resources
  • OSHA & ANSI Standards
  • Request a Quote
  • Contact
  • My Account

© 2026 Odiz Safety LLC. All rights reserved.

DUNS 080380452CAGE 7PX28
PrivacyTermsReturnsSafety Through Innovation

ODIZ

  1. Products
  2. /Standards
  3. /1910.212
  4. /1910.212(a)
  5. /1910.212(a)(3)
  6. /1910.212(a)(3)(iv)
  7. /1910.212(a)(3)(iv)(b)
OSHA Standard

OSHA 1910.212(a)(3)(iv)(b) – Shears

OSHA 1910.212(a)(3)(iv)(b) identifies shears as machines that usually require point-of-operation guarding to protect workers from serious hazards like cutting, shearing, and amputations.

5 products

OSHA 1910.212(a)(3)(iv)(b) — Shears

Under OSHA 29 CFR 1910.212(a)(3)(iv)(b), shears are among the equipment types that “usually require point-of-operation guarding” because their operation typically presents significant hazards at the cut zone.
Shears, which cut material by a downward blade motion or sliding blade action, create high risk of hand or finger entrapment, lacerations, and amputations if not properly guarded.

Why Shears Require Point-of-Operation Guarding

  • Cutting motion hazard: The shearing action of the blades converging presents a direct risk of severing.
  • High force application: Shears often apply substantial force to cut material, increasing potential injury severity.
  • Operator feed zone: Material is typically fed manually into the shear’s point of operation, creating exposure unless guard/interlock is in place.
  • Pinch & crush points: In addition to blade exposure, hold-down clamps or back-gauges may expose workers to pinch points.

Typical Safeguarding Methods for Shears

  • Fixed or adjustable barrier guards: To block access to the blade area during cutting, sized to prevent hand entry.
  • Interlocked guard doors or gates: Stops the machine if the guard is opened or removed before the cycle completes.
  • Two-hand controls or two-hand tripping devices: Forces operator’s hands to be away from the blade when a cut is initiated.
  • Presence-sensing devices and light curtains: For operations where manual feeding is necessary but still must ensure no body part enters the danger zone.
  • Back-gauge or hold-down clamp guarding: Shields the operator from pinch or crush hazards behind the blades or under the clamp.

Best Practice Compliance Checklist for Shears

  • Verify the blade area is fully guarded during the entire cutting cycle.
  • Ensure the guard prevents hand, finger, or body entry at any point of operation motion.
  • Check that any guard openings are sized to prevent access to the hazard zone and do not introduce new hazards (sharp edges, pinch points).
  • Confirm that interlocks, two-hand controls, or presence-sensing devices are in place and functioning correctly.
  • Inspect hold-down clamp and back-gauge mechanisms to ensure they’re guarded and do not permit reach-behind entry.
  • Document and test the safeguarding system prior to operation, especially after maintenance or blade changes.

FAQ

Does this standard apply to all types of shears?

Yes—all shearing machines that expose the operator or other employees to the point of operation hazard during normal use are subject to 1910.212(a)(3)(iv)(b).

Can manual feed shears without fixed guards rely solely on procedures?

No. Administrative controls alone are insufficient. Engineering controls—guards, interlocks, or presence-sensing devices—are required unless an equivalent safeguarding method is demonstrated.

What if the shear only cuts material occasionaly?

Even occasional use triggers the requirement. The standard lists “machines which usually require” guarding—but any machine with exposure must be safeguarded.

Showing all 5 products

Body Push Bar for ANSI B28.1-2017
CNC Plasma

Pressure Sensitive Push Body Bar - Barrier Guard and Estop

Pressure‑sensitive body bars are emergency‑trip devices required on rubber‑industry mills with roll heights at…

$1,350.00

SKU ODIZ-8527

View →
Press Brake Rear Guarding
Press Brake

Press Brake Rear Guarding

Odiz Press Brake Rear Guarding is an expandable, scissor-style press brake rear guard for the rear access area…

$3,995.00 – $28,168.00

SKU ODIZ-7897

View →
Lazer Safe Sentinel Plus
Press Brake

Lazer Safe Sentinel Plus

Brand: THCO

Sentinel Plus is the most advanced retrofit press brake guarding system, combining camera-based safety with hi…

Request quote

SKU ODIZ-7892

View →
three roller bending machine Estop Pull Cord Kit
Emergency Stop Controls

Odiz Three Roller Bending machine E-stop Pull Cord Kit

This three roller bending machine e-stop pull cord kit retrofits older 3-roller benders that have no safeties.…

$2,495.00

SKU ODIZ-7245

View →
Press 2 hand safety controls
H Frame Press

2 Hand Control Safety System

This two hand control safety system is a turnkey package for pneumatic presses: an 11 gauge heavy-duty steel h…

$5,999.00

SKU ODIZ-6773

View →