Safety Through Innovation · Made in the USA

574.318.4333Email UsODIZ AI Login
OdizSafety
ProductsServicesOdiz AICompany
Get an AssessmentGet an Assessment

Start a project

Let’s engineer a safer floor.

Schedule an AssessmentSchedule an Assessment
574-318-4333info@odiz.com
Odiz — Safety Through Innovation. Made in the USA.

Industrial safety, engineered from assessment through sustained compliance. Based in South Bend, serving manufacturers across North America.

Appearance

Solutions

  • Machine Safety
  • EHS Compliance
  • Laser Safety
  • Safety Software

Services

  • Machine Guarding Risk Assessment
  • Engineering & Design
  • Validation
  • All Services

Products

  • Machining
  • Metal Forming
  • Electronic Safety Enclosures
  • Accessories
  • All Products

Company

  • About Us
  • Resources
  • OSHA & ANSI Standards
  • Request a Quote
  • Contact
  • My Account

© 2026 Odiz Safety LLC. All rights reserved.

DUNS 080380452CAGE 7PX28
PrivacyTermsReturnsSafety Through Innovation

ODIZ

  1. Products
  2. /Standards
  3. /1910.213
  4. /1910.213(i)
  5. /1910.213(i)(3)
OSHA Standard

OSHA 1910.213(i)(3) – Guarding Requirements for Band Resaw Feed Rolls

OSHA 1910.213(i)(3) requires band resaw feed rolls to be guarded to prevent the operator’s hands from contacting in-running rolls. Guards must be made of heavy, preferably metal material, and positioned within three-eighths inch of the roll face in contact with the stock.

3 products

OSHA 1910.213(i)(3) — Guarding Requirements for Band Resaw Feed Rolls

OSHA 29 CFR 1910.213(i)(3) establishes mandatory guarding standards for feed rolls on band resaws used in woodworking operations.
This rule is designed to prevent operator hands and fingers from entering the hazardous in-running nip point where the feed rolls pull material into the blade.
The guard must be constructed from heavy-duty materials—preferably metal—and positioned precisely to provide full protection without interfering with feeding operations.

Regulatory Text


“Feed rolls of band resaws shall be protected with a suitable guard to prevent the hands of the operator from coming in contact with the in-running rolls at any point. The guard shall be constructed of heavy material, preferably metal, and the edge of the guard shall come to within three-eighths inch of the plane formed by the inside face of the feed roll in contact with the stock being cut.”

Purpose and Intent

Band resaws are used to cut lumber into thinner pieces or veneers by feeding material continuously through rotating rolls toward the moving saw blade.
The in-running nip point between these rolls presents a severe hazard, capable of pulling in hands, fingers, or loose clothing in a fraction of a second.
OSHA 1910.213(i)(3) ensures this danger is mitigated through the use of robust, close-fitting guards that physically prevent operator access to the in-running feed rolls.

Key Requirements

  • Guarding of feed rolls: A fixed or adjustable guard must cover the in-running area of the resaw’s feed rolls.
  • Material construction: The guard must be made from heavy material, preferably metal, strong enough to resist impact and wear.
  • Clearance distance: The edge of the guard must be positioned within three-eighths (3/8) inch of the plane formed by the inside face of the roll that contacts the stock.
  • Full coverage: Guards must prevent hand access from above, below, and the sides of the in-running point.
  • Non-interference: The guard must allow for continuous feeding of material without obstructing normal operation or visibility.

Common Hazards Controlled

  • In-running nip point injuries: Prevents hands and clothing from being drawn into the rollers.
  • Amputation risks: Protects against severe finger and hand injuries caused by roller entrapment.
  • Kickback: Properly designed guards stabilize feed motion and help prevent sudden ejection of stock.
  • Contact with moving parts: Reduces risk of accidental touch during setup or operation.

Design and Construction Guidelines

  • Use steel plate or cast metal guards to ensure long-term durability and impact resistance.
  • Ensure guard edges are smooth and rounded to prevent snagging of clothing or materials.
  • Position guards so the clearance from the roll face does not exceed 3/8 inch at any point along the length of the roll.
  • For adjustable guards, include secure locking mechanisms to prevent drift or misalignment.
  • Install fixed barrier extensions where operator reach zones may allow indirect contact with rolls.

Inspection and Maintenance Practices

  • Inspect feed roll guards daily for tightness, alignment, and structural integrity.
  • Measure guard clearance periodically to ensure it remains within the OSHA-specified 3/8-inch limit.
  • Replace or repair any bent, cracked, or missing guard sections immediately.
  • Check for proper clearance after any maintenance or feed roll replacement.
  • Ensure guards remain free from resin buildup, sawdust, or obstructions that may compromise visibility or clearance.

Best Practices for Compliance

  • Incorporate visual indicators or fixed stops to verify the guard’s position relative to the feed roll plane.
  • Train operators to never reach near in-running feed rolls while the machine is powered.
  • Include feed roll guarding checks in your daily machine inspection checklist.
  • Apply lockout/tagout procedures under OSHA 1910.147 when cleaning, adjusting, or changing feed rolls.
  • Document guard maintenance and inspections as part of your OSHA compliance records.

Why OSHA 1910.213(i)(3) Is Important

OSHA 1910.213(i)(3) addresses one of the most dangerous pinch points in woodworking machinery—the feed rolls of band resaws.
Without proper guarding, these rollers can pull an operator’s hands or clothing into the cutting path almost instantly.
By requiring heavy-duty, close-fitting guards positioned within three-eighths of an inch of the feed roll plane, this regulation provides critical physical protection that prevents severe entanglement, crushing, and amputation injuries.
Compliance with this standard ensures safer operation, longer machine life, and a lower risk of catastrophic accidents.

FAQ

Why must the guard be within three-eighths inch of the roll plane?

This clearance ensures there is no gap large enough for fingers or tools to enter the in-running point while still allowing stock to pass smoothly through the rolls.

Can the guard be made of material other than metal?

Yes, but OSHA prefers metal due to its durability and resistance to damage. Any substitute must offer equivalent strength and rigidity.

Are adjustable guards acceptable for varying stock sizes?

Yes, provided they remain securely fixed during operation and maintain the required three-eighths-inch clearance at all times.

Showing all 3 products

Vertical Bandsaw Guard angled view
Vertical Bandsaw

Vertical Bandsaw Guard

The ODIZ Safety Vertical Bandsaw Blade Guard is an adjustable safeguarding solution designed for vertical band…

$195.00

SKU ODIZ-9705

View →
three roller bending machine Estop Pull Cord Kit
Emergency Stop Controls

Odiz Three Roller Bending machine E-stop Pull Cord Kit

This three roller bending machine e-stop pull cord kit retrofits older 3-roller benders that have no safeties.…

$2,495.00

SKU ODIZ-7245

View →
safe belt guard
Belt and Coupling Guards

Custom Belt Guards

Odiz engineers and builds custom belt guards from four easy measurements. Match each measurement to the dimens…

$599.00

SKU ODIZ-1595

View →