Safety Through Innovation · Made in the USA

574.318.4333Email UsODIZ AI Login
OdizSafety
ProductsServicesOdiz AICompany
Get an AssessmentGet an Assessment

Start a project

Let’s engineer a safer floor.

Schedule an AssessmentSchedule an Assessment
574-318-4333info@odiz.com
Odiz — Safety Through Innovation. Made in the USA.

Industrial safety, engineered from assessment through sustained compliance. Based in South Bend, serving manufacturers across North America.

Appearance

Solutions

  • Machine Safety
  • EHS Compliance
  • Laser Safety
  • Safety Software

Services

  • Machine Guarding Risk Assessment
  • Engineering & Design
  • Validation
  • All Services

Products

  • Machining
  • Metal Forming
  • Electronic Safety Enclosures
  • Accessories
  • All Products

Company

  • About Us
  • Resources
  • OSHA & ANSI Standards
  • Request a Quote
  • Contact
  • My Account

© 2026 Odiz Safety LLC. All rights reserved.

DUNS 080380452CAGE 7PX28
PrivacyTermsReturnsSafety Through Innovation

ODIZ

  1. Products
  2. /Standards
  3. /1910.212
  4. /1910.212(a)
  5. /1910.212(a)(3)
  6. /1910.212(a)(3)(iv)
  7. /1910.212(a)(3)(iv)(c)
OSHA Standard

OSHA 1910.212(a)(3)(iv)(c) – Alligator Shears

OSHA 1910.212(a)(3)(iv)(c) lists alligator shears as machines that usually require point-of-operation guarding. These metal-cutting shears pose severe amputation and crush hazards, requiring fixed or interlocked guards to keep operators clear of the blade.

3 products

OSHA 1910.212(a)(3)(iv)(c) — Alligator Shears

OSHA 29 CFR 1910.212(a)(3)(iv)(c) identifies alligator shears as machines that usually require point-of-operation guarding.
Alligator shears, also known as lever shears, are used in scrap metal, recycling, and fabrication operations to cut bar stock, pipe, rebar, and other materials.
The hinged jaw mechanism, resembling an alligator’s mouth, creates a powerful shearing motion that can sever hands or limbs instantly if proper guarding is not installed.

Hazards of Alligator Shears

  • Amputation and laceration risks: The closing blades present a direct shearing hazard to hands and arms during feeding or removal of material.
  • Crush and pinch points: The hinge and clamping areas can trap body parts or clothing.
  • Unexpected movement: Hydraulic or mechanical actuation can cause accidental cycling if controls are damaged or improperly adjusted.
  • Flying debris: Fragments of cut material may be ejected from the cutting zone.

Required Guarding and Safeguarding Methods

  • Fixed barrier guards: Install rigid guards that enclose the blade and hinge area, leaving only the minimum opening necessary for material feed.
  • Adjustable feed guards: Use adjustable barriers or slots that allow different stock sizes while preventing hand entry into the cutting path.
  • Interlocked shields or covers: Require closure of a hinged shield before the machine will cycle; opening the guard halts motion.
  • Two-hand trip or control devices: For power-operated shears, controls must require both hands to activate, ensuring hands are away from the jaws during a cut.
  • Foot pedals with guards or covers: Pedals must be shrouded to prevent accidental activation by falling objects or unintended contact.

Safe Operating Practices

  • Feed stock with the free end down and away from the operator’s body to minimize kickback.
  • Use tongs, clamps, or push sticks to position short or small pieces—never feed by hand.
  • Inspect hydraulic and mechanical components daily for leaks, cracks, or control failures.
  • Ensure emergency stop controls are clearly visible, tested daily, and unobstructed.
  • Lockout and tag out before clearing jams, replacing blades, or performing maintenance.

Engineering and Design Considerations

  • Guard openings must comply with reach-distance standards to prevent hand or finger access.
  • Use impact-resistant materials or metal mesh for guards to contain flying fragments.
  • Provide adequate lighting and visibility around the feed area so operators can safely align material without removing guards.
  • Where possible, equip shears with automatic feed mechanisms or conveyors to eliminate manual placement of stock.

Common Violations

  • Operating with guards removed or missing around the blade or hinge.
  • Improper guard openings allowing finger or hand entry into the cutting zone.
  • Foot pedal not guarded or located too close to the operator.
  • Failure to use two-hand controls or interlocks where required.
  • No inspection or maintenance records for guarding systems.

Why OSHA 1910.212(a)(3)(iv)(c) Is Important

Alligator shears combine high mechanical force with exposed cutting motion, making them among the most dangerous tools in metalworking and recycling.
OSHA 1910.212(a)(3)(iv)(c) ensures that operators and helpers remain protected from amputation and crushing hazards through fixed or interlocked guarding, controlled operation, and proper training.
Compliance with this section is essential to maintain a safe environment around cutting and shearing stations.

FAQ

Are portable alligator shears covered under this rule?

Yes. Whether fixed or portable, alligator shears with powered blades must be guarded at the point of operation to prevent access to moving parts.

Can mesh guards be used?

Yes, provided the mesh opening size prevents finger access and the guard is durable enough to contain fragments and resist deformation.

Do foot-operated shears require additional protection?

Yes. Foot pedals must be guarded or shrouded to prevent accidental activation and should require deliberate pressure to engage.

Showing all 3 products

Body Push Bar for ANSI B28.1-2017
CNC Plasma

Pressure Sensitive Push Body Bar - Barrier Guard and Estop

Pressure‑sensitive body bars are emergency‑trip devices required on rubber‑industry mills with roll heights at…

$1,350.00

SKU ODIZ-8527

View →
Press Brake Rear Guarding
Press Brake

Press Brake Rear Guarding

Odiz Press Brake Rear Guarding is an expandable, scissor-style press brake rear guard for the rear access area…

$3,995.00 – $28,168.00

SKU ODIZ-7897

View →
three roller bending machine Estop Pull Cord Kit
Emergency Stop Controls

Odiz Three Roller Bending machine E-stop Pull Cord Kit

This three roller bending machine e-stop pull cord kit retrofits older 3-roller benders that have no safeties.…

$2,495.00

SKU ODIZ-7245

View →