Safety Through Innovation · Made in the USA

574.318.4333Email UsODIZ AI Login
OdizSafety
ProductsServicesOdiz AICompany
Get an AssessmentGet an Assessment

Start a project

Let’s engineer a safer floor.

Schedule an AssessmentSchedule an Assessment
574-318-4333info@odiz.com
Odiz — Safety Through Innovation. Made in the USA.

Industrial safety, engineered from assessment through sustained compliance. Based in South Bend, serving manufacturers across North America.

Appearance

Solutions

  • Machine Safety
  • EHS Compliance
  • Laser Safety
  • Safety Software

Services

  • Machine Guarding Risk Assessment
  • Engineering & Design
  • Validation
  • All Services

Products

  • Machining
  • Metal Forming
  • Electronic Safety Enclosures
  • Accessories
  • All Products

Company

  • About Us
  • Resources
  • OSHA & ANSI Standards
  • Request a Quote
  • Contact
  • My Account

© 2026 Odiz Safety LLC. All rights reserved.

DUNS 080380452CAGE 7PX28
PrivacyTermsReturnsSafety Through Innovation

ODIZ

  1. Products
  2. /Standards
  3. /1910.212
  4. /1910.212(a)
  5. /1910.212(a)(3)
  6. /1910.212(a)(3)(iv)
  7. /1910.212(a)(3)(iv)(a)
OSHA Standard

OSHA 1910.212(a)(3)(iv)(a) – Guillotine cutters

OSHA 1910.212(a)(3)(iv)(a) identifies guillotine cutters as machines that usually require point-of-operation guarding. Effective guards and devices must prevent hands from entering the blade area during cutting to avoid lacerations and amputations.

3 products

OSHA 1910.212(a)(3)(iv)(a) — Guillotine Cutters

Guillotine cutters use a descending knife to shear material (e.g., paper, plastic, thin metal, gasket stock).
Because the point of operation exposes workers to a sharp blade and clamping action, OSHA lists guillotine cutters as equipment that usually requires point-of-operation guarding.
Proper safeguards must keep hands and other body parts out of the danger zone for every cycle.

Primary Hazards

  • Amputation and deep lacerations from the descending knife.
  • Crush and pinch injuries from the hold-down clamp or back-gauge movement.
  • Unexpected cycling due to control or interlock failures.

Required Guarding Outcomes

  • Inaccessible blade: Guards or devices must prevent hand entry into the cutting zone during any stroke.
  • Safe clamping: Hold-down mechanisms must not create new pinch points or allow reach-around access.
  • Secure, durable construction: Guards remain in place under vibration and normal use and cannot be easily bypassed.

Common Safeguarding Methods for Guillotine Cutters

  • Fixed barrier or transparent hood covering the knife area with openings sized to block finger/hand access.
  • Interlocked front shield that prevents a cycle unless the shield is closed; opening the shield stops motion.
  • Two-hand controls (simultaneous actuation) that require both hands away from the blade to initiate each cut.
  • Presence-sensing devices (where appropriate) that stop hazardous motion if the sensing field is interrupted.
  • Rear guarding/back-gauge protection to eliminate reach-in from the back side of the table.
  • Hold-down clamp guards or shrouds that prevent fingers from entering between the clamp and table.

Best Practices

  • Use two-hand controls or interlocked shields as the primary safeguard; do not rely on procedures alone.
  • Verify safety distance and opening sizes so that hands cannot reach the blade before motion stops.
  • Provide anti-repeat controls and require a new two-hand command for each cut.
  • Perform pre-shift checks of interlocks, guards, two-hand controls, and emergency stop.
  • Lockout and tag out before changing knives, adjusting back-gauges, or clearing jams.
  • Train operators on safe feeding techniques—never hand-hold small stock in front of the blade; use push sticks, guides, or fixtures.

Compliance Checklist

  • Blade area guarded (fixed, interlocked, or device) — no hand access during the cut.
  • Two-hand control or equivalent safeguarding installed and functional.
  • Rear and side access points guarded; back-gauge movement not exposed.
  • Hold-down clamp guarded or designed to prevent pinch access.
  • Controls include anti-tie-down/anti-repeat; emergency stop accessible.
  • Daily functional tests documented; damaged guards or failed interlocks remove machine from service until corrected.

FAQ

Is a transparent front guard acceptable?

Yes, if it is impact-resistant, interlocked or fixed, and its openings and distance prevent finger/hand entry during the stroke.

Can procedures replace guards on a guillotine cutter?

No. Administrative procedures are not a substitute for point-of-operation guarding; engineering safeguards must physically prevent access.

Do older manual lever-type cutters need guarding?

Yes. Hand or foot-operated guillotines still present amputation hazards and usually require guards or two-hand controls to prevent hand entry.

Showing all 3 products

Press Brake Rear Guarding
Press Brake

Press Brake Rear Guarding

Odiz Press Brake Rear Guarding is an expandable, scissor-style press brake rear guard for the rear access area…

$3,995.00 – $28,168.00

SKU ODIZ-7897

View →
Extended boring mill adjustable guard
Horizontal Boring Mill

Horizontal Boring Mill Chuck Guard

The Odiz horizontal boring mill chuck guard adjusts in height and width to cover the chuck on horizontal borin…

$3,279.00

SKU ODIZ-7251

View →
three roller bending machine Estop Pull Cord Kit
Emergency Stop Controls

Odiz Three Roller Bending machine E-stop Pull Cord Kit

This three roller bending machine e-stop pull cord kit retrofits older 3-roller benders that have no safeties.…

$2,495.00

SKU ODIZ-7245

View →